C57BL/6 Mouse ADSCs/GFP

Price : $1500 $1800
Catalog No. : ADMC-C106G
Size : 1*10^6
Lead time : 3-4 weeks

These C57BL/6 Mouse Adipose Derived Mesenchymal Stem Cells/GFP are tested and free from contamination. It expresses multiple mesenchymal stem cell specific markers and has good proliferation and differentiation potential, which can differentiate into

Product name
C57BL/6 Mouse Adipose Derived Mesenchymal Stem Cells/GFP
Catalog No.
ADMC-C106G
Selection marker
GFP
Host cell line
Mouse GFP ADSCs
Adherent /Suspension
Adherent
Morphology
Fibroblast-like
Biosafety level
2
Application
Stem cell study
Differentiation
Complete culture media
ADSC culture medium
Freezing media
60% basel medium+30%FBS+10%DMSO
Special note
Please thaw the cells in T25. Please do not thaw the cells directly to a T75 flask or 10 cm culture dish.
Receiving and storage instructions
1.Upon arrival, check all containers for leakage or breakage.
2.Remove the frozen cells from the dry ice packaging and immediately place the cells at a temperature below -130°C, preferably in liquid nitrogen vapor, until ready for use. Please do not store at -80°C. Storage at -80°C may result in loss of viability.
Initial Handling procedure
1.Pipette 6-7 mL of complete medium into a 15 mL centrifuge tube.
2.Gently agitate the vial in a 37°C water bath to thaw. Please keep the O-ring and cap out of the water. Thawing should be rapid (approximately 1-2 minutes).
3.Remove the vial from the water bath as soon as the contents are thawed, and decontaminate by spraying with 70% ethanol or wiping with an alcohol cotton pellet. All of the operations from this point on should be carried out in the hood and under strict aseptic conditions.
4.Transfer the vial contents to the step 1 centrifuge tube containing 6-7 mL complete culture medium. And spin at 1100 rpm for 4 mins at room temp to collect the cells.
5.Resuspend cell pellet with 1ml recommended complete medium. And dispense into a T25 flask (or 6 cm culture dish) containing 4 mL of complete medium. (Note: It is suggested that, prior to the addition of the vial contents, the culture vessel containing the complete growth medium be placed into the incubator for at least 15 minutes to allow the medium to reach its normal pH 7.0 to 7.6.)
6.Incubate the culture at 37°C in a suitable incubator. A 5% CO2 in air atmosphere is recommended if using the medium described on this product sheet.
Subculturing procedure
1.When the cells are 80%-90% confluent, it is ready to passage. Remove and discard culture medium.
2.Rinse the cells 1-2 times with 1xPBS (2-3mL for T25 flask, increase or decrease the amount needed proportionally for culture vessels of other sizes) to remove residual medium and serum.
3.Add 1 mL of Trypsin-EDTA solution to T25 flask (increase or decrease the amount needed proportionally for culture vessels of other sizes) allow trypsin completely cover the cells, then place the flask into the incubator and incubate for 1-2 mins (if cells are hard to detach, allow appropriate extension of incubation), and observe cells under an inverted microscope until cell layer is dispersed. (Note: To avoid clumping do not agitate the cells by hitting or shaking the flask while waiting for the cells to detach.)
4.Add 2 times of trypsin vloume of complete growth medium to stop digestion, and aspirate cells by gently pipetting.
5.Transfer the cell suspension with a 10 mL pipette into a 50 mL centrifuge tube, rinse the residual cells from the flask with PBS , then collect to the centrifuge tube.
6.Centrifuge at 1100 rpm for 4 mins at room temp. Then remove and discard the supernatant and resuspend the cells with 2 mL of complete medium.
7.Dispense the cells into a suitable culture vessel containing corresponding amount of complete medium.
8.Incubate cultures at 37°C.
Vitro Biotech offers cell engineering products and services about KO cells, Luciferase cells, Cas9 expressing cell lines, and various stable cell lines.